top of page

Viking Rune Vambraces - Part I: The Leather

3 hours ago
4 min read

Watch the full build on YouTube: ten minutes, Part I of two.


Two words in Younger Futhark, two panels of vegetable-tanned leather, and a great deal of stitching. This is Part I of the build: everything that makes these vambraces a piece of leather. Part II is what goes inside them.

Two words, and the problem with runes

MISKUNN. LAUSN. Forgiveness, and redemption - written in Younger Futhark, the alphabet the Vikings actually used. Six runes on one arm, five on the other.

Runes are drawn with single strokes - one line, no thickness. At arm's length a hairline reads as nothing at all, and no font fixes that. Forty-four weights of the same typeface were measured, lightest to heaviest: across the whole range you gain roughly fifty percent of ink. What was needed was four hundred.

So the thickness gets built, not chosen. Offset the outline, weld the paths, and every stroke comes out around three millimetres wide - wide enough to read from three metres away.

Vegetable-tanned, and stapled flat

Vegetable-tanned only, and not for the look of it. Chrome-tanned leather under a laser releases things you do not want in a workshop, and no amount of extraction makes that a good idea. Veg-tan also takes dye evenly and burnishes properly, which matters more than usual here: on this piece the outside face is the whole piece.

The sheet comes off the roll, gets cut down against a plywood template, and then gets stapled flat to that board. It looks crude and it is the most important five minutes of the day. Leather off a roll wants to curl, and a sheet that lifts even a millimetre on the laser bed comes out with an engraving that fades across the panel.

What the laser engraves, and what it cuts

Alignment goes through the machine's camera: the artwork is dropped onto a live image of the actual sheet lying on the bed, not onto a guess about where it is.

Then the laser does two different jobs. It engraves - the Urnes-style beast across the top of each panel, and two braided bands running the width. And it cuts: the runes go all the way through the leather. They are not engraved into the surface. They are windows.

Everything after that is hand work. The outlines are cut with a knife and a steel rule, the straps are cut from the same hide, and the holes are punched.

The unglamorous hours

Edges cleaned up and burnished on a bench motor, every panel checked against its opposite number. A vambrace is a pair, and a pair gets judged on whichever one came out worse.

Dye, then oil, then antique, then Tan Kote

Dye first, worked in with a dauber. Then oil, to put back what the dye stripped out. Then an antique finish, worked across the surface and down into the engraving, where it settles in the cuts and lifts the beast and the braids out of the leather. Tan Kote last, to seal all of it in.

All of it on flat panels, before assembly. This is the order most people get backwards: leather finishing is wet and it is rough, and nothing about it gets easier once the piece has a shape.

Everything that holds is stitched

Then the longest stage, and the one that photographs worst. Everything is sewn by hand, two needles, in a stitching pony - every panel closed, every strap anchored. Not a drop of glue anywhere in this build.

The brass goes on in the same stretch. Eyelets down both sides of the opening, and the buckle hardware, each one set under an arbor press rather than hammered.

The fur is not stitched

A hide is cut to shape from the flesh side and laid inside the cuff, held by the lacing alone, so it can be pulled out, cleaned or swapped without touching a single stitch.

It also changes what the runes do. With the fur in, the windows stop reading as holes and start reading as dark letters - you read the words against the fur sitting behind them.

Two fastenings, and why both

A long leather lace runs criss-cross through the brass eyelets along the opening: that is what sizes the cuff to the arm and traps the fur. A separate strap and brass buckle close it over the top.

The lace is set once and left alone. The buckle is what you actually use to get the thing on and off.

Then you wear it

Properly. Bend, reach, flex, sit down with it on. Wearing a vambrace is a mechanical test: it pulls, it rubs, it folds. If something is going to fail, it fails here, in the workshop, and not in the middle of a convention.

End of Part I

MISKUNN. LAUSN. Forgiveness, and redemption - cut clean through the leather, with fur behind them. Part II is what lives inside.

Want a pair of your own

A vambrace has to fit the arm it is made for, so these are made to order rather than sold off a shelf. The word in the runes, the fur and the length of the cuff all change from one pair to the next. Commissions are open: start here - https://www.redsmithleatherwork.com/custom-order

And if you have a question about any step of this build, ask in the comments. I answer all of them.

Comments


bottom of page